Home > Error Rate > Lte Bler Definition

Lte Bler Definition

Contents

Bler_second returns the second BLER result, in percent (%). Using Different Power Levels on Downlink Timeslots The BLER results are calculated across all active downlink timeslots, not on any individual downlink timeslot. BLER just provides result either OK or NOT OK for each of the blocks. UL BLER can also be used to estimate the uplink transmission quality of a call.

Another possible correlation can be found when analyzing UL BLER and throughput of PS calls. Use the CALL:STATus:PDTCH:BLERror? Similar investigation could be done for triggering hard handover to different UTRAN frequencies or to different radio access technologies (RATs). Follow us! https://en.wikipedia.org/wiki/Block_Error_Rate

Lte Bler Definition

You can read more about HARQ in 36.321, sections 5.3 and 5.4. UL BLER is always high if throughput is low and vice versa. NAN (9.91E+37) case. 190 ! 200 !

  • Use the CALL:STATus:PDTCH:BLERror?
  • Programming Example 10 !
  • All Replies Posted by Don on 23 Jan 2012 3:57 PM The Block Error Rate (BLER) is a measure of how successful a data transmission is over the air at the
  • This query returns the percentage of blocks tested that were in error and the total number of blocks used to generate the BLER result.
  • Preview Email me at this address if my answer is selected or commented on:Email me if my answer is selected or commented on Privacy: Your email address will only be used
  • Retrieved 23 December 2015.
  • Due to the fact that UL BLER is only computed and used in the RNC internally it also is only available inside RNC software and as a rule is not shown
  • Can somebody please explain the procedure of Detach Request if it is triggered by Network.? +3 votes Can someone please explain RRC Connection Setup Procedure in lte ? +2 votes Can

Set the BCH level to -60 dBm 60 OUTPUT 714;"CALL:PDTCH:MSL:CONF D2U1" ! Monday, January 24, 2011 UMTS UTRAN BLOCK ERROR RATE (BLER) MEASUREMENTS Tweet Share Do you like this Article? Therefore, it makes sense to correlate RRC measurement reports as well as messages used to execute the RRC Active Set Update procedure with BLER measurements, because it helps to optimize settings Lte Bler Throughput Home Contact Privacy Policy Telecom Statistics 3G-LTE Mobile Broadband Cloud Computing Cognitive Radio Wireless Sensor Networks Ubiquity Networks and Internet Trending: Telecom Insights Tweet Subscribe Us Get free daily email

Configure BCH and PDTCH parameters 40 OUTPUT 714;"CALL:PDTCH:BAND PGSM" ! Bler In Telecom iBLER is initial BLER where as rBLER is residual BLER after retransmission. How would he propose without touching her? official site i think it should stop after a fixed Numbers of Attempts.

Reset the BLER results again using the SYSTem:MEASurement:RESet command. Bler Range In Lte I am using 3.09.19 , but after installation could not see any support for LTE in this tool. Use ctrl+k to highlight, ctrl+b to make the text as bold. This view was created using Qualcomm's QXDM tool.

Bler In Telecom

Attempts number to stop the RBLER procedure?? BLER is measured after channel de-interleaving and decoding by evaluating the Cyclic Redundancy Check (CRC) on each transport block. Lte Bler Definition Block Error Ratio Measurement Results Integrity Indicator Block Error Ratio The ratio of incorrectly received blocks to the total blocks sent to the UE, expressed as a percentage (%). Block Error Rate In Umts It is the receiver measurement used in conformance testing of GPRS/EGPRS mobiles.

If several credit sub-sessions will be used, all sub-sessions MUST be closed separately before the main session is closed so that units per sub-session may be reported. Starting or aborting a Block Error measurement does not affect the BLER reports. Get Trained Industry News About Us Contact Us More ... When in FDD Test Operating Mode , the test set does not monitor the uplink TFCI; rather, it assumes that a data block is sent in every TTI. Initial Bler Vs Residual Bler

Uplink adaptation is really up to the eNB vendor. What was the first ever James Bond film? Block error rate (BLER) is used for W-CDMA performance requirements tests (demodulation tests in multipath conditions, etc.). There are three major challenges in performance measurement namely: Defining performance measurements and KPIs, Verifying measurement results, Explaining measurement results.

commented Jan 16 by Salil Agrawal Your comment on this answer: Email me at this address if a comment is added after mine:Email me if a comment is added after mine Bler Meaning If the downlink on timeslot 4 degrades severely (and thus has a large number of block errors), the mobile station may be unaware of a request for Packet ACK/NACK messages. If the decoder is able to successfully decode the transmission, then no further action is needed; if it can't, HARQ can supply additional error correction information to improve the decoding results.

Details 7 Replies 1 Subscriber Postedover 4 years ago Options Subscribe via RSS Share this Ask the Expert HARQ This question is answered Posted by Djamschid (DJ) Mehrpuyan on 18 Jan

Uplink DTCH RMC CRC Presence UE Loopback Type The trigger source for this measurement is always protocol-based (see Trigger Source Description ). of -90 dBm(-60 dBm BCH level - 30 dB P0 level) 220 PRINT "Blocks tested at -90 dBm = ";Blocks_initial 230 PRINT "BLER Result at downlink PDTCH power of -90 dBm These extra blocks are included in the Blocks Tested , Block Error Ratio and Block Error Count results. Target Bler Lte You have posted to a forum that requires a moderator to approve posts before they are publicly available.

Also can you throw some light on Uplink Adaptation using Channel Quality and BLER . Feedback Buttons provided by Advanced Post Thanks / Like v3.1.6 (Lite) - vBulletin Mods & Addons Copyright © 2016 DragonByte Technologies Ltd. Set the multislot configuration to 70 ! Configure the BCH and PDTCH parameters using the CALL subsystem.